Sagem myx 5 manual

After entering your PIN code and the date and time, make your choice for the following settings: time zone, daylight savings, skin, wallpaper, screensaver, ring tone, volume, vibrate and voicemail number. If there are contacts saved in your SIM card, you are invited, if you wish, to copy them in the phone contacts memory. Using your phone Freeing the antenna The antenna is integrated in your phone, under the back cover at the top.

Avoid putting your fingers on this area when the phone is switched ON. If your fingers obstruct the antenna, the phone may have to operate with a higher power level than usual; decreasing its efficiency quickly. It could also affect the quality of your communications. Non ionising radiation To obtain maximum satisfaction from your phone, use it in a vertical position.

Your personal safety can only be improved by doing so. Increase the efficiency of your phone - Don't press the keys when not necessary: each keypress activates the backlight, and uses much power.

Hands-free mode During a call, press twice the key or the OK key to switch into hands-free mode. Charging the battery Your phone is powered by a rechargeable battery. A new battery must be charged for 4 hours at least before being used for the first time. It reaches its optimum capacity after a few cycles of use. When your battery has been discharged, the phone displays the state empty battery icon flashes.

In this case recharge your battery for at least 15 minutes before making any calls in order not to be cut off in the middle of a call. To recharge the battery: Connect the charger to a socket. Plug the end of the cable into the bottom connector of the phone. The phone is then charging up. The battery icon is scrolling up and down to indicate that it is charging.

When the battery is fully charged, the charging stops on its own. Disconnect the cable. When charging, the battery may warm up, this phenomenon is normal. Do not short circuit it. The battery does not have any part that you can change. Do not try to open the battery casing. Use only the appropriate chargers and batteries as shown in the phone manufacturer's catalogue. The use of other types of chargers or batteries may be dangerous or invalidate the warranty. Used batteries must be disposed of in the appropriate places.

We advise you to take the battery out if you plan not to use the phone for extended periods. You are strongly advised not to connect your phone to the charger if it doesnt contain a battery.

The charger is a safety step-down transformer, it is forbidden to modify, alter or replace it by another component power supply plug, etc. Phonebook The phonebook allows you to store numbers that you call regularly.

These numbers can be stored in the SIM card or in the phone. To store a contact in the phone memory, the following fields can be filled: last name, first name, numbers, email, URL, address, company, comments, ringtone, photo.

The fields coloured with red are mandatory. To store a contact in the SIM card, only the last name and number fields must be filled. The storage capacity will depend on the SIM card.

Please contact your network provider to get that information. Using the phonebook In the initial screen, press the T key to access the main menus. The first menu proposed is Phonebook. Press the OK key to enter the menu.

The list of your correspondents appears. By default, the cursor is positioned on the first name in alphabetical order. If you are using your phone and SIM card for the first time, the phonebook list will be empty, only the Contacts menu function will be available. Different icons inform you of the position in the phonebook where the contact is stored: contact stored in the SIM card contact stored in the phone if the Fixed Dialling option is activated, only those contacts may be called.

Adding a contact in the phone memory - Select the Contacts menu and press the OK key. The phone asks you to confirm the creation of a new list. Select Add contact each time you want to add a contact in the list. Memory Select Memory and validate.

Select SIM or Phone and validate. Phone: the screen displays the amount of memory used. The memory capacity is shared between the phonebook and various other features. If you lack memory, check if you can free some space from another feature. SIM: available memory only for contacts.

My numbers You can create the entries corresponding to your own numbers in order to consult them when necessary. Select My numbers and validate. Enter the different details and validate. Options from a contact saved Displaying a contact Select a contact from the list using the T S keys and press the OK key. The name and the number are displayed. Note: By directly pressing one character, the phone will display the first contact saved in the phonebook, starting with it.

To display the different options, select a contact from the list using the T S keys and press [Options]. Modify contact Modify what you want and validate then select Save once the modifications completed. Only the name and the first phone number will be copied. Delete Validate deletion of entry. My numbers See page Memory See page Mailing lists See page Calling a contact Several ways: - Select a contact. Press the key to start the call. Sending a vCard It is possible to send a vCard from each contact stored in the phonebook.

If the vCard is sent successfully, an information message is displayed. See Compose MMS on page Open the MMS from the inbox. Press [Options] and select Extract; select the vCard among the list of objects attached to this MMS, and add this contact to the phonebook by pressing the OK key.

A message is displayed to confirm the action. MMS is a Multimedia Message Service, which allows you to enclose audio files, images and others rich contents to your messages; these messages can even be composed of several slides. Please contact your network provider to get more information on their cost. This menu has been compiled in collaboration with magic4. Choose the SMS option. The language used is the one selected on the display of the phone if the language selected is not compatible with the Easy Message T9, the English language will be automatically selected.

When typing a text, a counter showing the number of characters deducted is displayed at the top of the screen depending on model.

This counter is not displayed if an icon or sound is inserted into the SMS. Messages The Easy Message T9 mode helps you to easily write your short messages.

Press once the key corresponding to the letter chosen and compose the word by continuing to press the keys corresponding to the various letters without paying attention to the display: the word is highlighted. If you agree on the word proposed on the screen, press the 0 key to validate it the 0 key inserts a space , and go on writing the next word. However, the same sequence of keys pressed can correspond to several words, existing on the dictionary.

If the word that appears is not the word you expected, press the TS keys to scroll through the words corresponding to this key sequence. Once you agree on the word proposed on the screen, press the 0 key to validate it the 0 key inserts a space , and go on writing the next word. If the word you are expected is not proposed, please add characters until you get the message Add the word?

Press Yes and validate if the word displayed suits you or modify this word before adding it in the dictionary. Messages In the input screen, the key is used to access other input options. Input modes When composing a message: Editor mode: The ABC mode is used to write words that do not exist in The navigation keys assume the the dictionary. To get a particular character, please press the following functions: corresponding key several times: the characters will scroll down on your - W key: screen.

Mode is used to add numbers. Last word Insert mode is used to add symbols, animations, call group icons and tunes. Images and sounds can be of two types: pre-defined or - X key: customized. Pre-defined images and sounds are smaller, especially Next word suited to exchanging messages.

Two short presses again, switches - key: back to lower case. Deletes last letter Punctuation characters - key: Punctuation characters are obtained thanks to key 1 except in Message options mode , or with the help of Insert mode fast access by briefly - key long press : pressing the key. Zoom mode changes size of Accented characters characters Accented characters are generated automatically in T9 mode.

Select the MMS option. When the text has been entered, [Options] is used to access the functions offered: Insert to insert multimedia objects such as images, animations and sounds into your message.

T9 options see page 26 ABC mode see page 27 mode see page 27 Slide to compose a slideshow of the multimedia objects. Preview to see a presentation of the multimedia objects. Cancel is used to delete all text entered and quit Saving the message Select Save. It is saved in the Drafts menu. You can enter an e-mail address. Note: It is possible that the voice message format. See your PC provider. Warning: some message sendings may fail if the message content is too big.

Add mailing list: this option allows you to select a mailing list to which the message is sent see chapter Phonebook. Add recipient: this option allows you to add another recipient. Add subject: this option allows you to add a subject to the message. Receiving messages When you receive a message, the phone plays the ring tone that you selected, and the message icon comes on the screen of your phone. If you do not read the messages, this icon remains displayed on the screen.

When it flashes, the memory is full. Receiving icons, backgrounds or tunes can take several seconds. An icon is blinking when the download of your message is in progress. Note that you have two different possibilities for receiving MMS: automatically or manually; if manual mode is activated, then you will receive only a notification in your Inbox, meaning that a MMS is available on the MMS Server; select Retrieve in the options when you want to retrieve the MMS from the server.

For more details about automatic and retrieval modes, see Sending options on page Please contact your network provider to get more information on icons, backgrounds or tunes downloading. Messages Received messages are stored in the SIM card or in the phone until you choose to delete them. Inbox On the Messages menu, please choose the Inbox menu and Select. Each message shows the presence of any attachments, the time and date the message was received and its size.

Messages are listed in chronological order, the latest one being displayed first. The quantity of Not Read and Not Retrieved messages is shown. Not Retrieved and Not Read messages are shown in bold.

Select a message and press the OK key. Choose one of the options given. Enclosures pictures or sounds , which you receive, can be extracted in order to be used later on stored. Outbox This menu displays the messages that failed to send. You can therefore try to send them again. Sentbox The Sentbox menu is used to store all your sent messages if you activated the option Store sent messages in the Options menu see page Too many messages saved will quickly fill up the available memory and no further messages will be received.

For each message, its characteristics shown with an icon and the time or date of sending are displayed on the screen. On the Messages menu, please choose the Drafts menu and press the OK key. Select a message and press [Options]. The options are: Delete, Read, Modify, Details. If you select a message and press the OK key, you can modify it. If you want to send it, select Modify then press [Options] and select Send. On the Messages menu, please choose Options and Select.

The SMS sending options are: message centre number, store sent message, acknowledgment, reply given, period of validity during that period, the network provider will try to send the message , message format. The MMS options are: - Store sent messages: it is highly recommended that you keep this function deactivated, in order to avoid a full memory , - Retrieval mode: if you are in a poor coverage area, it may be more convenient to choose the manual retrieval mode which gives you the retrieve later option.

Advanced settings: Send delivery report: sending a delivery report when receiving a message. Sender visibility: you choose to display or not your phone number on the receivers phone screen, with that message. Maximum size. On the Messages menu, please select the Memory option and Select.

The MMS screen displays how much memory is used in Kbytes. This menu is used to activate reception of local information broadcast by the Local information network. You can choose whether you want to receive this information or not please contact your network provider.

On the Messages menu, please select the Local info. Mailing list This menu displays the mailing lists created in the phonebook. To display the different options, press [Options]. Camera This menu allows you to take photos and use them for different purposes. For instance, you can send them to another phone or an Internet address, store them, use them as wallpapers or screen savers.

Take and send a photo Before taking a picture, some features need to be set. From the initial screen, press T or S to display the main menu and select the Camera menu. The camera is now on. Look into your phone display and position your subject. Move your phone to position your photo. Before taking a picture, there are various adjustment settings: - To activate one of the three available zoom levels, use the T S keys.

Warning: if you press [Back], you will go back to the previous screen and lose the photo you have just taken. If there is not enough memory to save the photo, a warning message appears, prompting you to confirm whether you want to go on. Once taken, the photo appears on the phone display. The name is made up with a number. Note: using the camera during a call may disturb the call quality.

The options are: - New Select one of the options with the T S keys and validate. Multimedia This menu gives you easy access to your favourite photos, pictures and sounds. On the Multimedia menu, please select the My Pictures menu and Select. The pictures stored are displayed on the screen. Please, use the T S keys to select one of them.

Once you have selected a picture, press [Options]. Select one of the options in the list with the T S keys and validate. Properties: properties of the picture selected. New photo: allows you to take a new picture. The Pictures menu allows you to delete all the pictures or to take a new photo. Select a photo and the Editor option, the Editor menu appears.

Select one of the edit functions with the T S keys and validate: - Sepia: allows you to change colors into sepia, - Zoom: allows you to magnify certain parts of your photo, - Adjustment: allows you to improve contrast, - Emboss: allows you to modify a photo with an embossed grey tint, - Negative: allows you to change a photo into negative, - Grey Scale: allows you to change color into black and white, - Add mark: allows you to add special characters or drawings to your photo, - Add frame: allows you to surround your photo with a frame, - Contrast: allows you to increase or decrease the contrast of your photo, - Sharpen: allows you to sharpen a photo, - Blur: allows you to add blur to a photo.

To access your sounds, use the same procedure as for your pictures see the My Pictures menu. This menu indicates the memory size used by the different features of Memory your phone. On the Multimedia menu, please select the Memory menu and Select. Use the T S keys to select the different features using memory. You can see the memory capacity used by each individual feature.

The WAP function allows you to log onto certain Internet sites. You can log onto sites that allow you to download ringtones, icons, animated screensavers, JavaTM applications to your phone. It contains the following sub menus: Welcome: logs onto the home page, carries the name of your access provider Bookmarks: is used to save in a phonebook the names and addresses The WAP navigator is the of Internet sites in order to make the access easy.

You can receive bookmarks from messages and add them to this list For this reason, it is forbidden to see chapter on SMS.

Inbox: this menu allows you to check the messages sent by the Internet site. You can activate the Save items: is used to save a WAP site items. History: backward and forward navigation of the pages displayed are kept in memory. Reload: refreshes the current page. Reset cache: clears the stored information on previous connections. Exit: returns to the phone's home page. Profiles is used to select or modify your access provider's logon parameters or configure the parameters of other access providers.

The active access service is preceded with a star. The Menu is used to add a new profile or to display the memory size available. On a profile in the list, press [Options], select Modify. GSM parameters: - Login - Password - IP address of WAP gateway - Port type secure or insecure - Dial-up number - Mode digital, analog or automatic In automatic mode access can be gained to the operator's network by a digital link and an analog link to a different network in roaming.

Select or add an APN. Once all the settings have been entered, you can activate the chosen access provider. Select him from the list. Validate your choice. Linger timer is used to choose the time after which the call is automatically disconnected if you have forgotten to log off from a service.

Once downloaded, they are stored in your phone's memory. You can then save them in your phone same operation as used for downloading using messages. WAP Logging off To log off, press the key. The logoff happens automatically after a few seconds of inactivity if you forget to log off.

This period is defined by the linger time setting. A non-flashing icon indicates that the GPRS network is available; if the icon is dark, it indicates that the phone is logged onto the GPRS network: see page 44 for the attachment options.

Games The games being designed by Java, many compatible games can be downloaded in your phone. The More games function allows you to download games connecting on a remote server. Depending on the operator, the connection URL may not be present.

Delete all menu: deletes all the games you have downloaded. Applications The Java function allows you to download applications and utilities in your phone. Please go to the Applications menu to use the applications already installed or install others. Services This item may not be present on your phones menu, as it depends on your SIM. Select one of the actions in the list with the T S keys and validate. Fill in the different items. Save the ToDo. ToDo actions menu This menu allows you to do all the actions possible on any ToDo.

Delete: allows you to delete the ToDo. Modify ToDo: allows you to modify the ToDo properties. Memory: allows you to view the memory used by the different functions of your ToDo. Categories: allows you to see the different ToDo categories, assign a specific ring tone to each individual ToDo, know the number of ToDos in each category and see them. You can send a vCal from each Todo task. Yet, this function is available only Sending a vCal on certain models of phone.

On the task list Todo main menu , please select a task and in the Todo task actions menu list select Send. When sending MMS, please select your contact information phone number or Email address before confirming. If you receive a call while you are sending a vCal, the call will have precedence. You cannot add the event to your diary until you have saved it.

You can assign a different beep to each Todo task. You can also assign a different ring tone to each Todo task category. To do this, you will need: - either to connect your phone to the PC by means of a suitable data cable serial or USB , - or to use the infrared function on your phone please refer to the Connectivity paragraph in the Settings Chapter. Next, you will have to install the "My Pictures and Sounds" software available from www.

Remark: If a call comes in during an exchange of data with your PC, the link will be interrupted and will have to be manually re-started.

On the Applications menu, please select the Calculator menu and OK. If no calculations are being run, pressing [Convert] allows you to use the value in the converter directly. Converter This menu allows you to convert one currency to another. On the Applications menu, please select the Converter menu and OK.

Enter a value and press the S key to convert from one currency to another, or the T key to convert back. Pressing [Options] allows you to use the following options: Rapid exchange If the Rapid exchange is activated, the converter will work in the initial screen by entering the desired numbers and pressing the S T keys to convert. Exchange rate Enter the exchange rate corresponding to the chosen currency.

Currency Enter the two types of currency to be converted. Go to calculator This option allows you to use immediately the value converted in the calculator. Applications The alarm works even when the phone is switched off. On the Applications menu, please select the Alarm menu and OK. Activate or Deactivate the alarm and validate. Set the wake-up time by entering the numbers directly or using the T S keys and validate. On the Applications menu, please select the Timer menu and OK.

The alarm icon appears on the initial screen. Organizer This menu gives you access to your diary and get to a day, week, month or specific date. It lets you add events, access the global actions for all the events and manage them by event category. This menu lets you add events, manage events by category, see the available Calendar menu memory and delete all the events.

From the Organizer menu, select the Calendar menu. Save the event. The other menus are: - See date: allows you to access events at a specific date. You can send a vCal from each diary event.

On the See today list, please select an event and in theTodo event actions menu list, select Send. For MMS deliveries, you should in addition select your contact information phone number or Email address before confirming.

You can assign a different beep to each diary event. You can also assign a different ring tone to each diary event category. This menu allows you to customize the ring tones on your phone and to Sounds activate beep and vibrate modes. Volume and ring tone This menu allows you to allocate a ring tone to each type of event. On the Sounds menu, please select the Ring tones menu and [Select]. Select the ring tone from the proposed list and validate.

Adjust the volume using the T S keys and validate. You can deactivate the sound by pressing the key. Vibrate This menu allows you to activate the vibrate mode for calls. On the Sounds menu, please select the Vibrate menu and [Select].

Select the vibrate mode from the proposed choices and validate. Silent mode This menu allows you to switch to Silent mode. On the Sounds menu, please select Silent mode and [Select]. Activate or deactivate Silent mode and validate. Silent mode can also be accessed via the initial screen by holding down the key. When the phone is in silent mode, the relevant icon appears on the initial screen. In this mode, the ring tone will not function, except for the alarm clock.

Note: if you have activated the silent mode, it does not remain after switching off your phone. Beeps This menu allows you to activate a beep for each type of event. On the Sounds menu, please select the Beeps menu and [Select]. Select the type of beep you want to allocate from the proposed choices Key beep, Network beep or Battery beep and validate.

Activate or deactivate the beep and validate. If you select key beeps, different options are given. Recorder These menu allows you to record you own melody.

On the Sounds menu, please select the Recorder menu and [Select]. Pressing [Start] record your melody or your voice by means of the microphone then save it. Give it a name and validate. This menu allows you to customize your screen by choosing a different Display presentation. This menu allows you to choose the skin of your phone, i. On the Display menu, please select Skins. Select the desired skin and validate. Skins are not downloadable but you can download screensavers and boot mode animations without changing those included by default with the skin.

Wallpaper This menu allows you to display the background picture you want on your phone. On the Display menu, please select the Wallpaper menu and [Select].

Select the wallpaper and [Visualise]. The picture appears in the background of the screen. Press [OK] to validate this choice, or [Back] to go back to choice. Note: the Diaporama option allows you to display a wallpaper scrolling different pictures in a random way. Screensaver This menu allows you to display an animation when the phone is in standby mode.

On the Display menu, please select the Screensaver menu and [Select]. Select one of the screensavers given and [Visualise]. The chosen screensaver appears on the screen, validate it. Operator logo This menu allows you to display your operator's logo on the initial screen. On the Display menu, please select the Operator logo menu and [Select].

Contrast This menu is used to adjust screen contrast. On the Display menu, please select the Contrast menu and [Select]. Adjust the contrast usings the Up S or Down T keys. Energy saving This function is used to deactivate the screen and the keypad backlight and consequently increase the battery life of your phone. On the Display menu, please select the Energy saving menu and [Select].

For Backlight two options are available: screen only and Full backlight. The screen goes out standby mode. To quit this mode, press the key. On the Settings menu, please select the Camera menu and [Select].

Timer: this menu enables you to take a photo with a 5, 10 or 15 second time delay. During preview of the photo, activate the delayed exposure by pressing on the button. NB: if you want to take the photo immediately, then press on the Photo button. Click sound: This menu allows you to select the sound you will hear when taking a photo.

Photo format: This menu allows you to choose the format in which your photo will be saved. There are several options: - either you systematically set the photo format to one of the following: High resolution or Mobile format, - or you can choose the photo format on a case-by-case basis.

Languages This menu allows you to choose your phone's display language. On the Settings menu, please select the Languages menu and [Select]. Select your language and validate. If you select Automatic, the language used will be the one relative to your SIM card. Calls The Calls menu allows you to manage all the calls functions call forward, displaying numbers, call waiting, voicemail number, etc.

Call forward Depending on your subscription, this service allows you to forward incoming calls to a different number or to the voice mailbox.

On the Calls menu, please select the Call forward menu and [Select]. Choose the type of forwarding you want from the options available. View last calls This menu allows you to access the list of last numbers used. On the Calls menu, please select the View last calls menu and [Select].

For every phone call are displayed on the screen: - its characteristics shown with an icon , - the time or date , - its duration. Select a call from the list and validate. You can also make the call by pressing the key. Fast access to the list of calls from the initial screen: press the key.

Counters This menu allows you to consult the duration of the up calls. It can also be used to check the volume of data exchanged in GPRS.

On the Calls menu, please select the Counters menu and [Select]. Select one of the options given. Display number This menu allows you to modify the status of the display number function. On the Calls menu, please select the Display number menu and [Select]. Select one of the options given: Anonymous mode, My number, Callers number.

Anonymous mode You have the facility to mask your number on the phone of the person you are calling. Preset: network default mode. No: you choose not to activate anonymous mode and then to display your number. Yes: you choose to active anonymous mode and then not to display your number. Settings During a call, you may be informed that a caller is trying to reach you: you hear a special tone.

The caller's identity is displayed on the screen name or number. Call waiting Operator-dependent service On the Calls menu, please select the Call waiting menu and [Select]. You can activate, deactivate, or consult the status of the call waiting service in order to check if it is active or not. During a call, if a second caller tries to contact you, the screen displays the call warning.

To use your phone, you have a small card called a SIM card. In addition to all of the information necessary for the network, this card contains other information that you can modify:. Your phone is compatible with the different SIM cards provided by the Operators.

There is a risk of explosion if the battery is incorrectly replaced or disposed of in fire. You are advised to remove the battery if you intend to leave your phone unused for a long period. Your phone is powered by a rechargeable battery. A new battery must be charged for at least 4 hours before it is used for the first time.

It will reach its nominal capacity after several usage cycles. The phone will start charging. The battery charging indicator indicates the charge. It is possible that during charging, the battery may heat up slightly; this is normal.

If your phone displays SIM absent, press long press to switch off your phone and check that your SIM card is correctly positioned.

If the wrong PIN code is entered three times in a row, the card will be locked. To unlock your card:. Contact your. Press to switch on your phone. This is the personal code for your SIM card.

You may be asked to enter this code when the instruction: Pin number? Enter the code of between 4 and 8 digits given to you by your operator. These digits will not be displayed on the screen for security reasons. Press or OK or on righthand key to validate. If one was given to you by your Operator, a second PIN code provides secure access to certain functions. If the battery has completely run down or been taken out, you will be asked to validate the time and date.

The indicator of the level of network signal received enables you to visualise the quality of reception. If it shows less than three bars, look for better reception to make your call in good conditions. Set the time either by typing it in or by using the scrolling arrows to alter the numbers already displayed.

Set the date either by typing it in numerically or by using the scrolling arrows to alter the display. When the time and date are correct, validate with the OK key. If the R letter and a network name are displayed, calls can be made. If the R letter is displayed without any network name, only emergency services will be accessible police, ambulance, fire brigade. If the flashes, the phone will keep searching. No network is available.

To directly access a menu, press then enter the number of the selected menu. Hold down the key until the end message is displayed. Your phone is equipped with an integrated antenna. For the best reception, try not to cover the top part of the phone with your hand. The menu functions permit you to verify or modify the various functions of your phone to adapt it to your needs. Press the scrolling arrows or to access the menus.

Scroll through the menus using the scrolling arrows then press OK to access the selected menu. Depending on the operator, you can contact the emergency services with or without a SIM card or when the keyboard is locked. It is sufficient to be in a zone served by a network. To call the international emergency service, dial then press. During the call, flashes on the screen, and tones may signal the establishment of a connection.

Press then speak. All incoming and outgoing call numbers are registered in the list of the last calls. Increase or decrease the volume during a conversation by pressing the lefthand or righthand key.

Before putting the phone to your ear, check the volume control settings as well as the selected listening method, especially if using integrated hands free mode, which could cause ear damage if used incorrectly. During a call, you can transfer from handset mode to hands-free mode simply by pressing one key and the reverse.

The quantity of phone numbers stored in the SIM card directory varies depending on the capacity of the card. You can verify the contents of a record and modify it by selecting the required name. When sorting by location, pressing on the key launches a search for the first available location; pressing on returns to the start of the list.

Different icons will inform you of the directory location where the number is stored when you search for it:. In the Directory menu , select Create record. Validate by pressing OK. Enter the name the number of accepted characters depends on the SIM card used. The figures entered after a space are processed in a DTMF sequence usable after a number. Depending on the available space, you can select the storage location of the number entered: SIM card or phone itself.

To delete the contents of a directory location, select the name using the scrolling arrows. Validate by pressing. Select Delete , then validate. You are also able to classify contacts recorded in the directory into Call Groups. To each of these groups you attribute certain characteristics icon, ringing tone, vibrator, etc.

Using the scrolling arrows, choose a group and press OK. You are then able to look up or alter its characteristics or to erase the group. Choose Create group. The selection of a call group is made when entering a number into the directory, or when modifying a number you have already saved. Choose Activate groups. The calls received from contacts who do not belong to a Call group use the parameters provided in the.

The first number shows the number of groups which can still be created, and the second shows the maximum number of groups. Choose See group. The screen presents the name, the icon, and the choice of vibrator mode of the group. If there are contacts attached to this group, press the righthand key to view the list of these ones.

Directory menu enables you to sort the stored numbers by name or location; for the latter, the free locations are indicated in the list. Select the recipient scrolling using the scrolling arrows and validate using OK. Select Send message and validate using OK. Press OK. Select Send and validate using OK. The recipient number is displayed.

Send your message using the righthand key. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Sagem myX-1 User Manual Download for 1. You have just bought a mobile phone and we congratulate you on your choice. We would like to remind you that this phone is approved to European standards.

AT is a registered trademark of Hayes Microcomputer products Inc. Hayes is a registered trademark of Hayes Microcomputer Products Inc. Depending on the model, the phone menus will appear as listed below: Services Directory Directory menu Sort by location Create record Call groups Available memory Personal numbers Quit Text messages Write new Contents Presentation of the phone Displaying personal numbers Contents Settings During a call, mind you do not obstruct the microphone with your hand.

Presentation of the phone The three keys located under the screen are allocated to actions described at the bottom of the screen just above the key, each time it is necessary. For example: Validate Pressing the righthand key validates the current function. Exchanging the front and back panel Switch off the phone. Getting started SIM card This card must be handled and stored with care in order to avoid excessive stresses or scratches that would damage it.

Note: Do not leave you SIM card within the reach of small children. Installing the SIM card and the battery Switch off your phone and disconnect the charger. Do not short-circuit. The battery does not contain any components that can be changed by you. Do not attempt to open the battery case. Spent batteries must be collected at the appropriate sites.

Charging the battery Your phone is powered by a rechargeable battery. When your battery has run down, the phone displays it and cuts out. To recharge your battery: Connect the charger to a wall outlet. Connect the end of the charging cable to the bottom of your phone. Charging stops by itself. Unplug the cable. Warning If the wrong PIN code is entered three times in a row, the card will be locked.